Universal Ambidextrous (Left / Right Hand) Outer Cabin Door Handle for Fiat, Ford & New Holland Tractors - Part Number: 65417006
The universal ambidextrous exterior cab door push-button handle (reversible LH / RH mounting) (part number 65417006, original OEM reference 5183633) is an ergonomic, heavy-duty manual release assembly designed to actuate the door latch mechanisms (compatible with LH latch 65417007 and RH latch 65417008) on agricultural tractor cabins across FiatAgri, Ford, and New Holland ranges. Molded from high-impact, UV-stabilized technical polymer with reinforced mechanical pivot linkages, it incorporates a smooth-operating push button and a dedicated cavity for the standard key lock cylinder barrel. Its symmetrical design permits immediate fitment on either the left-hand (driver side) or right-hand (passenger side) door, delivering a secure grip, positive weather sealing, and direct plug-and-play fitment across Fiat (M series), Ford (60 series), and New Holland (TL and TS series) tractors.
Key Features & Engineering Advantages
- Reversible Ambidextrous Design (LH / RH): Symmetric architecture allows straightforward mounting on either the left or right cab door, simplifying workshop spares management and eliminating fitting errors.
- High-Impact & UV-Resistant Technopolymer: Heavy-duty polymer casing engineered to withstand temperature extremes (-30°C to +80°C), intensive sunlight exposure, washdowns, agricultural chemicals, and hydraulic oils.
- Smooth Push-Button Release: Actuating mechanism equipped with a corrosion-resistant spring, ensuring crisp, low-effort door unlatching free of sticking or excessive mechanical play.
- Key Lock Barrel Housing: Factory-formed internal cavity accommodates the standard CNH master key lock cylinder, maintaining vehicle anti-theft security and key interchangeability.
- Environmental Perimeter Gasket Included: High-grade molded rubber base gasket seals the handle-to-door interface against rainwater, mud spray, and abrasive field dust ingress.
Technical Specifications
| Commercial Part Number |
65417006 |
| Mounting Position |
Ambidextrous – Left and Right Doors (LH / RH) |
| Original OEM Reference (Fiat / Ford / New Holland) |
5183633 |
| Component Classification |
Exterior cabin door push-button handle |
| Material Composition |
UV-stabilized reinforced technopolymer body with metal internal pivot pins and steel return spring |
| Actuation Method |
Push-button mechanical operation with key lock cylinder receiver cavity |
| Matching Latch Assemblies |
Directly couples with LH latch 65417007 and RH latch 65417008 |
Equipment Compatibility & Tractor Application Guide
| Manufacturer |
Tractor Series |
Supported Tractor Models |
| Fiat |
M Series |
M 100, M 115, M 135, M 160 |
| Ford |
60 Series |
8160, 8260, 8360, 8560 |
| New Holland |
TL Series |
TL70, TL80, TL90, TL100 |
| TS Series |
TS90, TS100 (11/97-7/03), TS110 (11/97-7/03), TS115 (7/01-7/03), TS115 (12/98-12/02) |
Installation Advice & Workshop Notes: To replace the handle, disassemble the interior door pillar trim to reach the rear securing hardware and disconnect the linkage rod retaining clip connected to the door latch (65417007 on LH or 65417008 on RH). If re-using the existing key barrel, release the internal retaining catch to transfer the lock cylinder into the new handle body. Ensure the molded rubber sealing gasket is seated flush against the exterior door sheet metal to keep moisture and dust out. Fasten the mounting screws progressively to avoid warping the polymer housing. Adjust the actuator rod length so that the push button has approximately 1–2 mm of free play before contacting the latch lever, ensuring smooth, low-effort operation and full door seal compression upon closure.
